Nodal Analysis

The aim of nodal analysis is to determine the voltage at each node relative to the reference node (or ground). Once you have done this you can easily work out anything else you need.

A node is all the points in a circuit

that are directly interconnected.

We assume the interconnections

have zero resistance so all points

within a node have the same

voltage. 

Five nodes: A, · · · ,E.

Ohm’s Law: VBD = IR5

KVL: VBD = VB − VD

KCL: Total current exiting any closed region is zero.

To find the voltage at each node, the first
step is to label each node with its voltage as follows

1. Pick any node as the voltage reference. Label its voltage as 0 V.

2. Assign node voltages to the other nodes.

3. Apply KCL to each node other than the reference node; express currents in terms of node voltages.

4. Solve the resulting system of linear equations for the nodal voltages.

Now, let us apply nodal analysis with voltage sources:

(Here, there are two cases we need to consider)

• Case 1: The voltage source is connected between a nonreference node and the reference node: The nonreference node voltage is equal to the magnitude of voltage source and the number of unknown nonreference nodes is reduced by one.

• Case 2: The voltage source is connected between two nonreferenced nodes: a generalized node (supernode) is formed.

Here’s the example of supernode:

A supernode is formed by enclosing a (dependent or independent) voltage source connected between two nonreference nodes and any elements connected in parallel with it.

The required two equations for regulating the two nonreference node voltages are obtained by the KCL of the supernode and the relationship of node voltages due to the voltage source. 

You already know the steps on how to apply nodal analysis in a circuit, so we will apply the same steps on the circuit with inductor and capacitor.

Just remember these formulas: for the inductor, use the formula jwL, where w is the omega, and L is the inductance, and for the capacitor, use the formula 1/jwC, where C is the capacitance. Getting the equivalent impedance( resistance in ac circuit), helps you in solving problems as you encounter this kind of circuit in the sample problems .

Learnings:


Nodal Analysis  is based on Kirchoff's Current Law.

A set of independent equations are generated by applying KCL at each unknown node.
When a KCL equation is written at a node, the unknowns in the equation are node voltages.

All node voltages are expressed relative to a ground node, therefore one node is assigned
to be ground or zero volts. Also in this chapter we learn that computing in AC is just the same as in DC.

"Impedance Combinations"

 Now that we've seen how series and parallel AC circuit analysis is not fundamentally different than DC circuit analysis, it should come as no surprise that series-parallel analysis would be the same as well, just using complex numbers instead of scalar to represent voltage, current, and impedance.

Being a series-parallel combination circuit, we must reduce it to a total impedance in more than one step. The first step is to combine as a series combination of impedances, by adding their impedances together. Then, that impedance will be combined in parallel with the impedance of the resistor, to arrive at another combination of impedances. Finally, that quantity will be added to the impedance  to arrive at the total impedance.

Learnings:

In this chapter we learn about series-parallel combination circuit.  Ac Analysis are the same with Dc Analysis. It only involves complex numbers.

"Impedance & Admittance"

AC steady-state analysis using phasors
allows us to express the relationship
between current and voltage using a
formula that looks likes Ohm’s law:
V = I Z
 Z is called impedance.

In the preceding section, we obtained the voltage-current relations for the three passive elements as,

V = RI, V = jωLI, V =I/jωC

These equations may be written in terms of the ratio of the phasor voltage to the phasor current as,

V/I = R,  V/I = jωL,  V/I = 1/jωC

From these three expressions, we obtain Ohm’s law in phasor form for any type of element as

Z = V/I    or   V = ZI

The impedance Z of a circuit is the ratio of the phasor voltage V to the phasor current I, measured in ohms.

The admittance Y is the reciprocal of impedance, 

measured in siemens (S).

The admittance Y of an element (or a circuit) is the ratio of the phasor current through it to the phasor voltage across it, or

Y   =   1/Z   =   I/V

Some Thoughts on Impedance

• Impedance depends on the frequency ω.

• Impedance is (often) a complex number.

• Impedance allows us to use the same

solution techniques for AC steady state as

we use for DC steady state.

"Phasor in Circuit Elements"

Phasors allow us to express current-voltage relationships for inductors and capacitors much like we express the current-voltage relationship for a resistor.How to represent a voltage or current in the phasor or frequency domain, one may legitimately ask how we apply this to circuits involving the passive elements R, L, and C. What we need to do is to transform the voltage-current relationship from the time domain to the frequency domain for each element. Again, we will assume the passive sign convention.

We begin with the resistor. If the current through a resistor 

R is i = Im cos(ωt + φ),

 the voltage across it is given by Ohm’s law as 

v = iR = RIm cos(ωt + φ)

Figure representation: 

Sinusoid & Phasor

Introduction

Any (non-pathological) function can be represented by an appropriate superposition of sine waves of

different frequencies, either as a Fourier series or as a Fourier integral. The response of a linear network toa composite sinusoidal signal can be determined for each sinusoidal term separately, and the overall

response then obtained by superposition. This is in part the basis of the fundamental importance of the

analysis of the response of a linear circuit to a single sinusoid of

 arbitrary frequency. Circuit behavior for

composite signals can be inferred from knowledge of this sinusoidal response. Hence what is considered

in this course primarily is the analysis of a linear circuit with an arbitrary

single-frequency sinusoidal

excitation.

We now begin the analysis of circuits in which the source voltage or current is time-varying. In this chapter, we are particularly interested in sinusoidally time-varying excitation, or simply, excitation by a sinusoid. 

  

A sinusoid is a signal that has a form of the sine or cosine function.

v(t) = Vm sinωt

Vm=the amplitude of the sinusoid

ω=the angular frequency in radians/s

ωt=the argument of the sinusoid

A periodic function is one that satisfies v(t) = v(t+nT), for all 

t and for all integers n.

While...

A phasor is a complex number that represents the amplitude and phase of a sinusoid.

Arithmetic With Complex Numbers